Electric Pumps

New this season! We are now stocking the non-clogging electrical, submersible, dewatering pump from Site Drainer. The free flow of the cylinder in this pump allows the water to continue to flow freely even after a solid particle barrier is created. Conquer the mud, rain and flood with it’s wide selection of pump applications, including submersible, centrifugal, discharge, trash, and diaphragm.

BJM Pumps: Gas and Electric

1. R Series

The Bullet R Series pumps are ideal for dewatering construction sites, mines, or for all around use in industrial plants and utilities.

• Top Discharge. Allows for superior cooling of motor and provides a slim line design.
• Longer Power Cord. Standard 33ft. power cord on pumps ½ HP and below and 50ft. on pumps 1HP and above.
• 304SS Motor Housing. Superior abrasion resistance will not wear out like aluminum motor housings when pumping sandy water.
• Three Seal Motor Protection. The motor is protected by double mechanical seals. The lower seal is made of silicon carbide/silicon carbide and the upper seal is made of carbon/ceramic. An additional lip seal has been installed above the impeller, to help prevent abrasives such as dirt, silt or sand, from entering into the seal chamber.
• More Motor Protection. Winding protection and (NEMA) Class F motor insulation allows motor temperature to raise to 230°F and is superior to pumps with Class A and B insulation. Automatic switch turns the pump motor off if the temperature and/or amp draw raises too high. When the motor cools the switch will automatically reset and the pump will turn back on.
• Tough Pump Construction. Hardened cast iron stands up to rough handling and pumping sandy water unlike pumps with soft resin impellers or plastic exterior components.

2. SV-Series Trash Pump

The SV-pumps are equipped with Vortex impellers, undoubtedly the best non-clog impellers ever invented for the handling of mud, raw sewage, viscous liquids, rags, wood chips and other solids. They pass solid up to 90% of the pump outlet diameter.

• Longer Power Cord. Standard 33ft. power cord on pumps ½ HP and below and 50ft. on pumps 1HP and above.
• 304SS Motor Housing. Superior abrasion resistance will not wear out like aluminum motor housings when pumping sandy water.
• Three Seal Motor Protection. Motor is protected by double mechanical seals. The lower seal is made of silicon carbide/silicon carbide and the upper seal is made of carbon/ceramic. An additional lip seal has been installed above the impeller, to help prevent abrasives such as dirt, silt or sand, from entering into the seal chamber.
• More Motor Protection. Winding protection and (NEMA) Class F motor insulation allows motor temperature to raise to 230°F and is superior to pumps with Class A and B insulation. Automatic switch turns the pump motor off if temperature and/or amp draw raises too high. When the motor cools the switch will automatically reset and the pump will turn back on.
• Tough Pump Construction. Hardened cast iron stands up to rough handling and pumping sandy water unlike pumps with soft resin impellers or plastic exterior components.

Tsurami Pumps – Electrical

1. LB Series

• Top discharge provides maximum motor cooling while allowing continuous duty operation.
• Single-phase or three-phase.
• Pumps fit into 8-inch pipes.
• Urethane Semi Vortex Impeller and elastomer lined pump casing for maximum wear life.

2. NK Series

• Heavy Duty, high head single phase pumps.
• 110v or 220v.
• Optional agitator kits allow continuous duty when pumping abrasive materials.
• Synthetic Rubber Wear Parts for maximum durability and pump performance.
• Continuous duty, air-filled motor.
• Ductile iron semi-vortex impeller.
• Dual voltage available on NK2-15 model.

Get Electric Pumps for Your Upcoming Job

Request a Quote or call us at 1-888-776-0007  to speak with a Pro Tool & Supply representative for more information on our variety and large stock of electric pumps.